Technical orders (TO) provide all of the following pertaining to the inspection operation, maintenance, and modification of Air Force (AF) equipment and material except

policy directives.

Simply stated, a technical order (TO) is considered to be

a military order.

Technical orders (TO) are established, numbered, and issued in accordance with which TO?

00–5–1.

Which type of technical order (TO) covers installation, operation, troubleshooting, repairing, removing, calibration, and servicing or handling of Air Force military systems?

Operations and maintenance TOs.

Enhanced Technical Information Management System (ETIMS) provides a direct on-line connectivity from every base into the management system to allow all except

most current publication date.

To find the most current publication date of a technical order (TO), check

the TO index.

The Maintenance Integrated Data Access System (MIDAS) is

a six-digit numbering system expressed as three elements of two digits each.

What information does the nondestructive inspection (NDI) general system (GS) manual provide?

Inspections.

What type of equipment manual would contain equipment calibration requirements?

Operation and service manual.

A group assembly parts list has several part numbers listed for a part you need. To determine which part number is right for your aircraft, refer to the

Usable on Code column.

Where would you find information for recording and reporting a nondestructive inspection(NDI) technique to inspect an F–16C aircraft speed brake?

TO 33B–1–1.

You are tasked to do an inspection; however you only know the name of the part you are toinspect. To locate the applicable paragraph and figure number for the inspection, check the technical order’s (TO)

alphabetical index.

While doing a job you find a mistake in a technical order (TO). Correcting this requires initiation of a Technical Manual Change Recommendation and Reply form. Who is responsible for this action?

You.

Which change recommendation priority must be answered within 40 calendar days?

Urgent.

Which type change recommendation priority is used to recommend improvements to correct potential hazards?

Routine.

Which technical order (TO) contains complete instructions for maintaining TOs?

00–5–1.

Electronic technical orders (eTO) are files identified by a media distribution code suffix of

–WA-n.

You need to order a new technical order (TO) for personnel use on a regular basis; how would you accomplish this action?

Establish an ID requirement.

The technical order (TO) listing for your shop’s operational TO file will show you all of the following except

who currently has one signed out.

Responsibility for consolidating technical order (TO) requests on an installation rests with the

personnel in the TODO.

With few exceptions, you must file technical orders (TO) within a maximum of

five workdays of receipt.

A technical order (TO) effective date is

later than the basic date.

In which technical order (TO) chapter would you find page 4–2?

4.

File technical order (TO) supplements in

reverse numerical order in front of the basic TO.

Enhanced Technical Information Management System (ETIMS) will be updated automatically in no more than how many days?

7 calendar days.

Who has ownership of Air Force supplies and equipment?

The American taxpayer.

The purpose of the Air Force supply system is to

provide a standard means of purchasing, distributing, and controlling equipment/supplies required by the Air Force.

Which system is used to determine whether your nondestructive inspection (NDI) laboratory is authorized a piece of equipment?

AFEMS.

Which form is used to request an item not listed in the Federal Supply System?

DD Form 1348–6.

Which condition tag would be placed on an eddy current unit being sent back to depot for repair?

Green DD Form 1577–2.

All of these are requirements for an initial journeyman skill level except you must

complete 9 months of on-the-job training.

From the lowest to the highest, what are the three levels of maintenance capability?

Organizational, intermediate, depot.

Which level of maintenance involves major repairs and overhaul?

Depot.

Which inspection involves a thorough and searching review of an entire weapon system?

Periodic (PE).

Which inspection attempts to minimize the length of time an aircraft is down for inspection?

Phase (PH).

Which inspection is based on calendar days?

Isochronal (ISO).

Which maintenance symbol would be used to indicate a scheduled periodic (PE) inspection is overdue?

Red dash.

Which symbol signifies that an unsatisfactory condition exists?

Red diagonal.

Category I deficiency reports (DR) are not used to report conditions

resulting from nonconformance to specifications.

Maintenance data documentation (MDD) is grouped into what categories?

On- and off-equipment.

You would not find maintenance data documentation (MDD) rules in

TO 00–35D–54.

Maintenance information system (MIS) refers to an automated maintenance information system that supports and enables what?

Maintenance business processes.

Which maintenance data documentation (MDD) code is used as the primary method of sorting information?

Work unit.

The Air Force maintains a limited number of these maintenance data documentation (MDD) codes to simplify reporting?

How malfunctioned.

Which is not a maintenance inspector function?

Verify the quantity of modified parts is correct.

All engine flight data can be found on Air Force Technical Order (AFTO) Form

781J.

What is the correct format for entering a date in the 781 series forms?

YYYYMMDD.

Which blocks are used by nondestructive inspection (NDI) personnel to clear all red dash discrepancies?

Inspected by and employee no. blocks.

What is used to record service, periodic, and special inspections, and the current status of equipment?

AFTO 244.

What indicates a special inspection or operational check is due, a scheduled inspection is overdue, and the equipment is in an unknown condition?

A red dash.

What is a database developed for the nondestructive inspection (NDI) career field in an effort to reduce paper and improve the management of process controls and equipment maintenance?

PCAMS.

What are commanders, staff officers, and supervisors responsible for when it comes to accident prevention?

Enforcing standards and regulations.

The minimum temperature required for a substance to initiate self-sustained combustion is known as the

ignition temperature.

The danger from static electricity is highest during

cold, dry weather.

All of these have the potential for serious injury, when wearing jewelry except

wearing gloves on the hand to prevent injury.

Which personal protective equipment is not normally used in the nondestructive inspection (NDI) lab?

Long sleeves.

Engine position numbers on multi-engine aircraft are assigned consecutively from the

tip of the left wing to tip of the right wing.

Where is an aircraft elevator located?

On the empennage.

The tie-down rings on aerospace ground equipment (AGE) are normally attached to the

frame.

Aerospace ground equipment (AGE) power system components are not made from

copper.

How are permanent joints on aerospace ground equipment (AGE) enclosures normally attached?

Riveted.

How many standard markings are applied to all Air Force aircraft?

Six.

Where are station numbers located on fixed wing aircraft?

Nose.

Which is not an aircraft identification and safety marking?

Crew.

What symbol is used to indicate an installed ejection system?

Triangle with apex pointed down.

What small and subdued safety marking alerts you to a hazardous condition?

Warning text.

Depending on the type of aircraft and engine, how big is the noise safety zone circle surrounding the aircraft?

300 to 400 feet.